NEW DAMS IN PAKISTAN

government of Pakistan has so far constructed 49 small dams and plans to build eight more in Rawalpindi, Jhelum, Attock and Chakwal areas in order to promote agriculture in these regions.

According to an official of the Ministry of Water and Power, construction of the six small dams is expected to be completed during the current financial year which would help irrigate around 12,310 acres of agricultural land.

The dams include Darmalak Dam (Kohat), Lawaghar and Karak Dam (Karak), Khair Bara Dam (Haripur), Jabba Khattak Dam (Nowshera) and Palai Dam (Charsadda).

“The feasibility study is being done on 11 more dams. Some of them will be built in 2011-12 while others in 2012-13,” he added.

He further said that the 12 dams would be constructed in two phases in all the four provinces with storage capacity of four MAF water. In the first phase Winder and Naulong dams will be constructed in Balochistan, Kurram Tangi in Khyber-Pakhtunkhwa, Darwat and Nai Gaj in Sindh and Ghabir Dam in Punjab.

The provincial government has allocated Rs1 billion for Punjab Agriculture Research Board and also doubled the budget for the improvement of research infrastructure.

South Korean Firm To Install 300MW Solar Power Plant In Pakistan’s Baluchistan Province

Pakistan’s largest province, by area, Baluchistan is rich in mineral resources, and while it is highly strategically located near Iran and the rest of Pakistan, it remains quite underdeveloped. Over the past few years, foreign companies have forged partnerships with the provincial government for extraction of valuable minerals from the area. Now a Korean company plans to set up a solar power plant which can bring prosperity and growth to the region. K Solar Korea has signed a Memorandum of Understanding with the Baluchistan government to set up a 300 MW solar power project near the province’s largest city, Quetta. The project is expected to require $900 million investment. The project will bring relief to the province which, like the rest of the country, is suffering from acute power shortage. The project will also help the province increase self-reliance in the energy sector. While the province is the gateway to Pakistan’s much needed energy supplies from neighbouring Iran, it lags behind most parts of the country in economic development. Despite being very rich in natural resources and being the largest province in the country, Baluchistan’s contribution to Pakistan’s GDP has been less then 5% between 1973 and 2000. 

Due to the predominantly tribal lifestyle of the population of the province, urbanisation has had limited penetration. The importance of infrastructure development in the region cannot be overstated. The need for sustainable energy infrastructure also stems from the fact that several foreign companies are now looking to set up exploration and extraction businesses in the province. With the development of such industries it is essential that substantial growth in the clean energy infrastructure takes place so that the pristine ecosystem of the province is preserved as much as possible.

Pakistan has taken up several large renewable energy projects in recent years as it aims for a sustainable future to counter its resource-strained present. In addition to it’s large-scale projects, the provincial governments have launched innovative measures to popularise the use of clean energy. The Punjab government distributed solar PV modules to students who faired well in their high school examinations. Such measures may eventually help the country raise an army of highly skilled clean energy professionals who could help the country out of its energy crunch.

Welding Electrodes in Pakistan

DIAMOND WELD RODS (Pvt) LTD and

SHANGHAI INDUSTRIES (Pvt) LTD

ISO 9001:2008 Certified Company

Manufacturer of Welding Electrodes in Pakistan, both companies are well renowned in Pakistan and producing a variety of good quality electrodes and competing with all other manufacturers and importers especially China brand. Brand of these companies are very famous in Pakistan with affordable prices. Company main suppliers in Pakistan are:- 

  Aslam & Sons, Kashmir Road, Rawalpindi (051-5568274)
Bilal Traders, Lahore
Muhammad Sajid, Vehari
Muhammad Hanif, Chowk Shaheedan, Multan
Punjab Hardware, Peshawar

Comapny was established in early 80s with a firm conviction and determination of enhancing and advancing the welding line by giving it a new dimension and by introducing high standard welding electrodes and accessories. Famous brands are:-

Pak Bridge

Diamond Brand

POWER SUPPLIES

To supply the electrical energy necessary for arc welding processes, a number of different power supplies can be used. The most common classification is constant current power supplies and constant voltage power supplies. In arc welding, the voltage is directly related to the length of the arc, and the current is related to the amount of heat input. Constant current power supplies are most often used for manual welding processes such as gas tungsten arc welding and shielded metal arc welding, because they maintain a relatively constant current even as the voltage varies. This is important because in manual welding, it can be difficult to hold the electrode perfectly steady, and as a result, the arc length and thus voltage tend to fluctuate. Constant voltage power supplies hold the voltage constant and vary the current, and as a result, are most often used for automated welding processes such as gas metal arc welding, flux cored arc welding, and submerged arc welding. In these processes, arc length is kept constant, since any fluctuation in the distance between the wire and the base material is quickly rectified by a large change in current. For example, if the wire and the base material get too close, the current will rapidly increase, which in turn causes the heat to increase and the tip of the wire to melt, returning it to its original separation distance.[1]

The direction of current used in arc welding also plays an important role in welding. Consumable electrode processes such as shielded metal arc welding and gas metal arc welding generally use direct current, but the electrode can be charged either positively or negatively. In welding, the positively charged anode will have a greater heat concentration and, as a result, changing the polarity of the electrode has an impact on weld properties. If the electrode is positively charged, it will melt more quickly, increasing weld penetration and welding speed. Alternatively, a negatively charged electrode results in more shallow welds.[2] Non-consumable electrode processes, such as gas tungsten arc welding, can use either type of direct current (DC), as well as alternating current (AC). With direct current however, because the electrode only creates the arc and does not provide filler material, a positively charged electrode causes shallow welds, while a negatively charged electrode makes deeper welds.[3] Alternating current rapidly moves between these two, resulting in medium-penetration welds. One disadvantage of AC, the fact that the arc must be re-ignited after every zero crossing, has been addressed with the invention of special power units that produce a square wave pattern instead of the normal sine wave, eliminating low-voltage time after the zero crossings and minimizing the effects of the problem.[4]

Duty cycle is a welding equipment specification which defines the number of minutes, within a 10 minute period, during which a given arc welder can safely be used. For example, an 80 A welder with a 60% duty cycle must be "rested" for at least 4 minutes after 6 minutes of continuous welding.[5] Failure to observe duty cycle limitations could damage the welder. Commercial- or professional-grade welders typically have a 100% duty cycle.

Welding Joints

Welding joints are formed by welding two or more workpieces, made of metals or plastics, according to a particular geometry. The most common types are butt and lap joints; there are various lesser used welding joints including flange and corner joints.

Butt welds

Butt welds are welds where two pieces of metal are joined at surfaces that are at 90 degree angles to the surface of at least one of the other pieces.^[1] These types of welds require only some preparation and are used with thin sheet metals that can be welded with a single pass ^[2]. Common issues that can weaken a butt weld are the entrapment of slag, excessive porosity, or cracking. For strong welds, the goal is to use the least amount of welding material possible. Butt welds are prevalent in automated welding processes, such as submerged-arc welding, due to their relative ease of preparation.^[3] When metals are welded without human guidance, there is no operator to make adjustments for non-ideal joint preparation. Because of this necessity, butt welds can be utilized for their simplistic design to be fed through automated welding machines efficiently.

Types

Butt joint geometries

There are many types of butt welds, but all fall within one of these categories: single welded butt joints, double welded butt joint, and open or closed butt joints. A single welded butt joint is the name for a joint that has only been welded from one side. A double welded butt joint is created when the weld has been welded from both sides. With double welding, the depths of each weld can vary slightly. A closed weld is a type of joint in which the two pieces that will be joined are touching during the welding process. An open weld is the joint type where the two pieces have a small gap in between them during welding.

[edit]

Square butt joints

The square-groove is a butt welding joint with the two pieces being flat and parallel to each other. This joint is simple to prepare, economical to use, and provides satisfactory strength, but is limited by joint thickness. The closed square butt weld is a type of square-groove joint with no spacing in between the pieces. This joint type is common with gas and arc welding.

For thicker joints, the edge of each member of the joint must be prepared to a particular geometry to provide accessibility for welding and to ensure the desired weld soundness and strength. The opening or gap at the root of the joint and the included angle of the groove should be selected to require the least weld metal necessary to give needed access and meet strength requirements.

[edit]

Bevel butt joints

Single-bevel butt welds are welds where one piece in the joint is beveled and the other surface is perpendicular to the plane of the surface. These types of joints are used where adequate penetration cannot be achieved with a square-groove and the metals are to be welded in the horizontal position ^[4]. Double-bevel butt welds are common in arc and gas welding processes. In this type both sides of one of the edges in the joint are beveled.

[edit]

V-joints

Single-V butt welds are similar to a bevel joint, but instead of only one side having the beveled edge, both sides of the weld joint are beveled. In thick metals, and when welding can be performed from both sides of the work piece, a double-V joint is used. When welding thicker metals, a double-V joint requires less filler material because there are two narrower V-joints compared to a wider single-V joint. Also the double-V joint helps compensate for warping forces. With a single-V joint, stress tends to warp the piece in one direction when the V-joint is filled, but with a double-V-joint, there are welds on both sides of the material, having opposing stresses, straightening the material.

[edit]

J-joints

Single-J butt welds are when one piece of the weld is in the shape of a J that easily accepts filler material and the other piece is square. A J-groove is formed either with special cutting machinery or by grinding the joint edge into the form of a J. Although a J-groove is more difficult and costly to prepare than a V-groove, a single J-groove on metal between a half an inch and three quarters of an inch thick provides a stronger weld that requires less filler material. Double-J butt welds have one piece that has a J shape from both directions and the other piece is square.

[edit]

U-joints

Single-U butt welds are welds that have both edges of the weld surface shaped like a J, but once they come together, they form a U. Double-U joints have a U formation on both the top and bottom of the prepared joint. U-joints are the most expensive edge to prepare and weld. They are usually used on thick base metals where a V-groove would be at such a extreme angle, that it would cost too much to fill.

[edit]

Others

Thin sheet metals are often flanged to produce edge-flange or corner-flange welds. These welds are typically made without the addition of filler metal because the flange melts and provides all the filler needed. Pipes and tubing can be made from rolling and welding together strips, sheets, or plates of material.^[5]

Flare-groove joints are used for welding metals that, because of their shape, form a convenient groove for welding, such as a pipe against a flat surface.

The Tee Butt Weld is formed when two bars or sheets are joined perpendicular to each other in the form of a T shape. This weld is made from the resistance butt welding process.

Selection of the right weld joint depends on the thickness and process used. The square welds are the most economical for pieces thinner than 3/8”, because they don’t require the edge to be prepared.^[6] Double-groove welds are the most economical for thicker pieces because they require less weld material and time. The use of fusion welding is common for closed single-bevel, closed single J, open single J, and closed double J butt joints. The use of gas and arc welding is ideal for double-bevel, closed double-bevel, open double-bevel, single-bevel, and open single-bevel butt welds.

Below are listed ideal joint thicknesses for the various types of butt welding joints. When the thickness of a butt weld is defined it is measured at the thinner part and does not compensate for the weld reinforcement.

Workpiece thickness limits per joint type^{[citation needed]}

Joint type	Thickness
Square joint	Up to 1⁄4 in (0.64 cm)
Single-bevel joint	3⁄16–3⁄8 in (0.48–0.95 cm)
Double-bevel joint	Over 3⁄8 in (0.95 cm)
Single-V joint	Up to 3⁄4 in (1.9 cm)
Double-V joint	Over 3⁄4 in (1.9 cm)
Single-J joint	1⁄2–3⁄4 in (1.3–1.9 cm)
Double-J joint	Over 3⁄4 in (1.9 cm)
Single-U joint	Up to 3⁄4 in (1.9 cm)
Double-U joint	Over 3⁄4 in (1.9 cm)
Flange (edge of corner)	Sheet metals less than 12 gauge[clarification needed]
Flare groove	All thickness

Cruciform

Diagram of a cruciform joint between 3 plates of metal

A cruciform joint is a specific joint in which four spaces are created by the welding of three plates of metal at right angles. In the American Bureau of Shipping Rules for Steel Vessels, cruciform joints may be considered a double barrier if the two substances requiring a double barrier are in opposite corners diagonally. Double barriers are often required to separate oil and seawater,chemicals and potable water, etc.^[7]

[edit]

Plate edge preparation

In common welding practices, the welding surface needs to be prepared to ensure the strongest weld possible. Preparation is needed for all forms of welding and all types of joints. Generally, butt welds require very little preparation, but some is still needed for the best results. Plate edges can be prepared for butt joints in various ways, but the five most common techniques are oxyacetylene cutting (oxy-fuel welding and cutting), machining, chipping, grinding, and air carbon-arc cutting or gouging. Each technique has unique advantages to their use.

For steel materials, oxyacetylene cutting is the most common form of preparation. This technique is advantageous because of its speed, low cost, and adaptability. Machining is the most effective for reproducibility and mass production of parts. Preparation of J or U joints is common prepared by machining due to the need for high accuracy. The chipping method is used to prepare parts that were produced by casting. The use of grinding to prepare pieces is reserved for small sections that cannot be prepared by other methods. Air carbon arc welding is common in industries that work with stainless steels, cast iron, or ordinary carbon steel.^[8]

Welding Procedure Specification

A Welding Procedure Specification (WPS) is a formal document describing weldingprocedures. The purpose of the document is to guide welders to the accepted procedures so that repeatable and trusted welding techniques are used. A WPS is developed for each material alloy and for each welding type used. Specific codes and/or engineering societies are often the driving force behind the development of a company's WPS. A WPS is supported by a Procedure Qualification Record (PQR or WPQR). A PQR is a record of a test weld performed and tested (more rigorously) to ensure that the procedure will produce a good weld. Individual welders are certified with a qualification test documented in a Welder Qualification Test Record (WQTR) that shows they have the understanding and demonstrated ability to work within the specified WPS.

The following are definitions for WPS and PQR found in various codes and standards:

According to the American Welding Society (AWS), a WPS provides in detail the required welding variables for specific application to assure repeatability by properly trained welders. The AWS defines welding PQR as a record of welding variables used to produce an acceptable test weldment and the results of tests conducted on the weldment to qualify a Welding Procedure Specification.

The American Society of Mechanical Engineers (ASME) similarly defines a WPS as a written document that provides direction to the welder or welding operator for making production welds in accordance with Code requirements.^[1] ASME also defines welding PQR as a record of variables recorded during the welding of the test coupon. The record also contains the test results of the tested specimens.

In Europe, the European Committee for Standardization (CEN) has adopted the ISO standards on welding procedure qualification (ISO 15607 to ISO 15614) and on welder qualification (ISO 9606), with the exception of qualification for steel welders, where a new version of the old european EN 287-1 standard still applies. EN ISO 15706 defines a WPS as "A document that has been qualified by one of the methods described in clause 6 and provides the required variables of the welding procedure to ensure repeatability during production welding". The same standard defines a Welding Procedure Qualification Record (WPQR) as "Record comprising all necessary data needed for qualification of a preliminary welding procedure specification". ^[2] In addition to the standard WPS qualification procedure specified in ISO 15614, the ISO 156xx series of standards provides also for alternative WPS approval methods. These include: Tested welding consumables (ISO 15610),Previous welding experience (ISO 15611), Standard welding procedure (ISO 15612) and Preproduction welding test (ISO 15613).

In the oil and gas pipeline sector, the American Petroleum Institute API 1104 standard is used almost exclusively worldwide. API 1104 accepts the definitons of the American Welding Society code AWS A3.0.^[3]

[edit]

Gas Welding

The most common gas welding process is oxyfuel welding, also known as oxyacetylene welding. It is one of the oldest and most versatile welding processes, but in recent years it has become less popular in industrial applications. It is still widely used for welding pipes and tubes, as well as repair work. It is also frequently well-suited, and favored, for fabricating some types of metal-based artwork. Oxyfuel equipment is versatile not only because it is preferred for some sorts of iron or steel welding but also because it lends itself to brazing, braze-welding, metal heating (for bending and forming), the loosening of corroded nuts and bolts, and also is the ubiquitous means for oxy-fuel cutting of ferrous metals.

The equipment is relatively inexpensive and simple, generally employing the combustion ofacetylene in oxygen to produce a welding flame temperature of about 3100 °C. The flame, since it is less concentrated than an electric arc, causes slower weld cooling, which can lead to greater residual stresses and weld distortion, though it eases the welding of high alloy steels. A similar process, generally called oxyfuel cutting, is used to cut metals.^[6] Other gas welding methods, such as air acetylene welding, oxygen hydrogen welding, and pressure gas welding are quite similar, generally differing only in the type of gases used. A water torch is sometimes used for precision welding of small items such as jewelry. Gas welding is also used in plastic welding, though the heated substance is air, and the temperatures are much lower.

[edit]

Resistance

Resistance welding involves the generation of heat by passing current through the resistance caused by the contact between two or more metal surfaces. Small pools of molten metal are formed at the weld area as high current (1000–100,000 A) is passed through the metal. In general, resistance welding methods are efficient and cause little pollution, but their applications are somewhat limited and the equipment cost can be high.

Spot welder

Spot welding is a popular resistance welding method used to join overlapping metal sheets of up to 3 mm thick. Two electrodes are simultaneously used to clamp the metal sheets together and to pass current through the sheets. The advantages of the method include efficient energy use, limited workpiece deformation, high production rates, easy automation, and no required filler materials. Weld strength is significantly lower than with other welding methods, making the process suitable for only certain applications. It is used extensively in the automotive industry—ordinary cars can have several thousand spot welds made by industrial robots. A specialized process, called shot welding, can be used to spot weld stainless steel.

Like spot welding, seam welding relies on two electrodes to apply pressure and current to join metal sheets. However, instead of pointed electrodes, wheel-shaped electrodes roll along and often feed the workpiece, making it possible to make long continuous welds. In the past, this process was used in the manufacture of beverage cans, but now its uses are more limited. Other resistance welding methods include flash welding, projection welding, and upset welding.^[25]

[edit]

Energy beam

Energy beam welding methods, namely laser beam welding and electron beam welding, are relatively new processes that have become quite popular in high production applications. The two processes are quite similar, differing most notably in their source of power. Laser beam welding employs a highly focused laser beam, while electron beam welding is done in a vacuum and uses an electron beam. Both have a very high energy density, making deep weld penetration possible and minimizing the size of the weld area. Both processes are extremely fast, and are easily automated, making them highly productive. The primary disadvantages are their very high equipment costs (though these are decreasing) and a susceptibility to thermal cracking. Developments in this area include laser-hybrid welding, which uses principles from both laser beam welding and arc welding for even better weld properties, and X-ray welding.^[26]

[edit]

Solid-state

Like the first welding process, forge welding, some modern welding methods do not involve the melting of the materials being joined. One of the most popular, ultrasonic welding, is used to connect thin sheets or wires made of metal or thermoplastic by vibrating them at high frequency and under high pressure. The equipment and methods involved are similar to that of resistance welding, but instead of electric current, vibration provides energy input. Welding metals with this process does not involve melting the materials; instead, the weld is formed by introducing mechanical vibrations horizontally under pressure. When welding plastics, the materials should have similar melting temperatures, and the vibrations are introduced vertically. Ultrasonic welding is commonly used for making electrical connections out of aluminum or copper, and it is also a very common polymer welding process.

Another common process, explosion welding, involves the joining of materials by pushing them together under extremely high pressure. The energy from the impact plasticizes the materials, forming a weld, even though only a limited amount of heat is generated. The process is commonly used for welding dissimilar materials, such as the welding of aluminum with steel in ship hulls or compound plates. Other solid-state welding processes include co-extrusion welding, cold welding, diffusion welding, exothermic welding, friction welding (including friction stir welding), high frequency welding, hot pressure welding, induction welding, and roll welding.^[27]